vin 814

Describe these cars here or do a restoration blog of your DeLorean

Re: vin 814

Postby andyd » Sun Aug 30, 2020 11:08 am

Cheers mike, yeah, am chuffed!
andyd
 
Posts: 1185
Joined: Wed Jan 26, 2011 6:24 pm
Location: North London
VIN #: 814

Re: vin 814

Postby bandit » Sun Aug 30, 2020 12:56 pm

Nice, looks great Andy :dmcdoors: :dmcdoors:
User avatar
bandit
 
Posts: 2104
Joined: Tue Jul 14, 2009 11:22 am
Location: Derbys
VIN #: 7024
Spaxed

Re: vin 814

Postby Domi » Sun Aug 30, 2020 3:42 pm

This is really beautiful :P
Domi Vin#16951
User avatar
Domi
 
Posts: 996
Joined: Mon Jun 08, 2009 11:48 am
Location: France
VIN #: 16951
Spaxed

Re: vin 814

Postby eric » Sun Aug 30, 2020 4:04 pm

That is the nicest fascia I have ever seen.... Top job.
7161

There is only one thing in life worse than not owning a DeLorean.
Owning one which is not running...
User avatar
eric
 
Posts: 453
Joined: Wed Jul 18, 2018 10:44 am
Location: Nantwich - Cheshire
VIN #: 7161
Spaxed

Re: vin 814

Postby DMC1983 » Sun Aug 30, 2020 4:24 pm

Top drawer ol' chap. :clap: :clap: :clap:

mkovb.jpg
mkovb.jpg (89.53 KiB) Viewed 23372 times
DeLoryan
VIN 5219 - Oct 81
Grey Interior, Manual
Grooved Hood
Reg:  FNP 478W (Finding Numerous Problems)
Travelling And Recreation Developed In Style
Member of the Beverley Hills Car Club Club
User avatar
DMC1983
 
Posts: 1113
Joined: Thu Oct 22, 2015 7:51 pm
Location: Essex
VIN #: 5219
Spaxed

Re: vin 814

Postby cis6409 » Mon Aug 31, 2020 11:07 pm

Quality work there! great to see
User avatar
cis6409
 
Posts: 724
Joined: Tue Jun 09, 2009 9:59 pm
VIN #: 6409

Re: vin 814

Postby Admin-bloke » Wed Sep 02, 2020 4:28 pm

Great to see the results there. Very nice.
Admin-bloke, "The D Whisperer"
Pie n Pint Northerner....
Vin #4068 - y'official "Mighty Auto" test car for Admin-bloke tuning.

https://www.justgiving.com/campnibble

Forum Founder [means I just installed it........] and Tech Help
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
Admin-bloke
 
Posts: 5300
Joined: Thu May 28, 2009 6:45 pm
VIN #: 4068
Spaxed

Re: vin 814

Postby andyd » Mon Sep 07, 2020 9:37 pm

One of the things I did recently with the fascias off was to get the front (amber) and rear (red) side markers wired up properly.

Previously I (? or someone prior- its been too long!) had disconnected the rear markers. I had wired the front side markers to act as repeaters for the indicators. They therefore did not come on with "position 1" of the headlight switch. My front indicators did not have the low current filament, simply the high current one flashing as per UK indicators.

I wanted to return to OEM configuration, but with a slight modification. I wanted the front side marker to come on with "position 1", but also to flash with the indicator.

Crucially, I did not want it to flash out of phase with the front indicator. I wanted to on with the indicator, and off with the indicator, not "opposite" to what the front indicator was doing. Similarly, with "position 1" (and position 2) I also wanted it to be a solid "on" when not indicating...

Get it?

So basically, its on with any headlight, but effectively flashing "off" in phase with the indicator...

Unless no headlights are on, and then its just an indicator repeater.

I also didn't want to butcher my wiring loom.

Clever old Dan Stacy came up with a very nice way to achieve this. He suggested an adjustable N555 timer.

https://en.wikipedia.org/wiki/555_timer_IC

This measured potential difference to the indicator feed, and when the indicator flashes, it cuts the sidemarker function. Once the flashing stops, the solid side marker comes back on.

The timer (which is adjustable) is just very slightly longer than the interval of the indicator flash.

The sidemarker thus gets a positive pulse with the indicator no matter what. So with the headlight switch in "position 0" (no lights at all), the amber side marker is a repeater.

At position 1 (and 2), it comes on constantly. When you indicate, it cuts the "solid on" power, and then you see the flash. After you stop indicating, it comes on constant again.

I know that this is all a pointless waste of time for something that doesnt really matter, but I think pulling out of junctions, motorcyclists (for example) may not see the little siver car turning right with a (dual filament) front indicator and no side marker. Similarly, changing lanes on the motorway is bad enough, but with constant on side markers there is even less to signal to fuckwit road users that you want to pull out.

So I got these:

IMG-20200613-WA0005.jpeg
IMG-20200613-WA0005.jpeg (1.2 MiB) Viewed 23269 times


A box (in a fact I went through a few, for stupid trial and error reasons)
Connectors to go "in line" where the 3-wire front indicator loom plugs in. So a female and male needed
The timer module (something like

https://www.ebay.co.uk/itm/Adjustable-T ... SwjFleC0GM ).

And wired it so that it goes in between these two familiar connectors behind the front grille

20200617_181745.jpg
20200617_181745.jpg (3.84 MiB) Viewed 23269 times


It looks then like this:

20200829_081511.jpg
20200829_081511.jpg (3.62 MiB) Viewed 23269 times


And finally, like this.

20200829_074256.jpg
20200829_074256.jpg (3.58 MiB) Viewed 23269 times


So you can see where this plugs in-line. And the single lead on a spade connector then goes to feed the side marker (minimal butchery- not quite none! But mine had been hacked about anyway, so Mike W cant shout at me)

This then all lives behind the front dummy grille. If I were clever, I could post a video of it all lit up like a christmass tree, but I'm not, so I cant.

But I would be very pleased to discuss at length over a beer when we can all meet up again!! :thumbsup: :lol:

Its may a bit of pointless mod, but perhaps an element of safety, and I didnt want out-of-phase side marker flashing, and I think this is a good way to do it. Or at least Dan did, and told me what to do. Thanks mate, very much appreciated.

Its the little things that make us happy right? And this does that.

See you later

Andy
andyd
 
Posts: 1185
Joined: Wed Jan 26, 2011 6:24 pm
Location: North London
VIN #: 814

Re: vin 814

Postby Dan 6511 » Mon Sep 07, 2020 10:32 pm

Awesome, glad you got it working. If you WhatsApp me a video I can put it on youtube and link it on here if you want.
Sell it Or Sorn it

Road trips:
2008: Mervyn's Delorean Weekend, Ireland
2008: DMC Europe Open House
2009: DMC Europe Open House
2009: Royal Delorean Weekend, Ireland
2010: Silvercoast, France
2010: Shanefest, Ireland
2010: Luxemburg & Nurburgring
2011: Eurofest, Belfast
2019: International DeLorean Meeting, Hamburg
User avatar
Dan 6511
 
Posts: 3538
Joined: Fri Jun 05, 2009 5:10 pm
Location: Essex

Re: vin 814

Postby BABIS » Tue Sep 08, 2020 2:00 pm

I achieved the same result with 2 of these modules: https://www.oznium.com/led-controllers/ ... ack-driver
the only limit is that they can be used just with leds (very small wirings)
BABIS
 
Posts: 127
Joined: Wed Aug 17, 2011 2:23 pm

PreviousNext

Return to Members Cars or Unique DeLoreans

Who is online

Users browsing this forum: No registered users and 9 guests

About us

The DeLorean Club UK forum for European DeLorean owners and enthusiasts. The largest DeLorean forum in Europe.

Registration is FREE and all registered users get full access

cron