Look what I've got back....

Describe these cars here or do a restoration blog of your DeLorean

Re: Look what I've got back....

Postby A Van » Mon May 08, 2017 12:48 pm

That's where I was heading!


Sent from my iPhone using Tapatalk Pro
Alistair V

Vin 11753 - B/Auto - Kuwait, painted black
Ex Vin 11766 - B/Auto - Dubai
Ex 11622, 6064

RIP Mike 'Bozzy' Bosworth 19/04/1969 - 31/12/2015


Official Spokesperson and Media Liaison Officer, and off road Buggy flipper
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
A Van
 
Posts: 7813
Joined: Fri May 29, 2009 6:33 pm
VIN #: 11753
Spaxed

Re: Look what I've got back....

Postby MikeWard » Mon May 08, 2017 1:13 pm

InoX wrote:Fitted 5.25" speakers in the back - not exactly drop in replacements. Had to cut back the carpet and foam to get to the fibreglass then had to shim the magnet on the bottom to get the things to fit.

Made the mistake of getting front speakers with protruding tweeters which mean't I had to space them away from the dash. Hours spent trying to guide the screws and washers up vertically whilst on my back at the same time trying to prevent the fasteners from being pinched by the magnets :x

What speakers did you go with for the rear? (I used Infinity Kappa 52.9i on my car, and they clamped in without the need for any fettling).

For the fronts, did you bend the mounting tabs up and out as per the below pics, that should help a little with the protruding tweeter.
front_speakers0.jpg
front_speakers0.jpg (35.67 KiB) Viewed 4496 times

front_speakers2.jpg
front_speakers2.jpg (51.94 KiB) Viewed 4496 times
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
MikeWard
 
Posts: 1781
Joined: Thu Dec 17, 2009 11:49 pm
Location: Egham, Surrey
VIN #: 04708

Re: Look what I've got back....

Postby DJK73 » Mon May 08, 2017 2:51 pm

Did you run new speaker cable or split the old circuit?
Dbro4
Ex Vin#10223
Grey interior, Manual
Spaxed
Free flow
User avatar
DJK73
 
Posts: 275
Joined: Tue Mar 31, 2015 12:55 pm
VIN #: 10223
Spaxed

Re: Look what I've got back....

Postby InoX » Mon May 08, 2017 3:17 pm

Bent the tabs slightly placed a half nut 1/4 way down the stud to space the speaker. Then bent the tabs up a bit.

Yes, there's new cable. Removed the old crap.

The speakers are jbl 5020s I think.
User avatar
InoX
 
Posts: 465
Joined: Sat Jun 20, 2009 2:51 pm

Re: Look what I've got back....

Postby InoX » Mon May 08, 2017 5:29 pm

Yep. just seen the order

I got these:

JBL CLUB 3020 - 3.5" 8cm 2-Ways Coaxial Car Speakers 120 Watts JBL CLUB 3020 1
JBL CLUB 5020 - 5.25" 13cm 2-Way Coaxial Car Speakers 240 Watts JBL CLUB 5020 1
Kenwood KDC-164UR - CD/MP3, Front USB, Front AUX KEN-KDC-164UR 1
Rockford Fosgate RFWP16-30 16 AWG Speaker Wire Packaged 30 Foot Black/Silver ROC-RFWP16-30 1
Connects2 CT27UV08 Universal Electric Aerial CON-CT27UV08 1

So I suppose the lesson is don't get either the 3020 or the 5020 because neither are easy drop in.

It's a fine line between a nice neat fix and a bodge. I hope that I've done a nice neat fix 8-) :shifty:
User avatar
InoX
 
Posts: 465
Joined: Sat Jun 20, 2009 2:51 pm

Re: Look what I've got back....

Postby MikeWard » Tue May 09, 2017 10:02 am

InoX wrote:So I suppose the lesson is don't get either the 3020 or the 5020 because neither are easy drop in.


For reference, these speakers should be drop in. The fronts are for sure as I used them on #4463:
Front (note, the mounting tabs will need to be bent as per the previous pictures I posted, but other than that they drop straight in):
http://caraudiosecurity.com/hertz-dcx87 ... 3-speakers

Rear (I used Infinity Kappa 52.9i in #4708 and #4463, however this model is no longer available, that said, these Infinity Reference speakers should fit the same)
http://caraudiosecurity.com/reference-5 ... w-speakers
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
MikeWard
 
Posts: 1781
Joined: Thu Dec 17, 2009 11:49 pm
Location: Egham, Surrey
VIN #: 04708

Re: Look what I've got back....

Postby Daniel Shane » Tue May 09, 2017 12:14 pm

I fitted some Sony 6x9's in a custom rear board.

Made it out of MDF, covered it in automotive carpet and fitted in perfectly under the rear window.

Saved all the faf of trying to get a good fit in the original holes, no trim to remove and sounded great. Also with the cargo net in place they were invisible.
Dan Shane
DCUK 008
Ex VIN 4754

The Black Stig
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
Daniel Shane
 
Posts: 461
Joined: Fri Jun 05, 2009 1:29 pm
VIN #: Ex 4754

Re: Look what I've got back....

Postby InoX » Sun May 21, 2017 2:49 pm

afternoon.

put the fuel system back together after getitng some more parts (fuel pump, stainless brace, tank hoses, filter...)

primed the system a bunch of times to check for leaks and found that fuel was pissing out of the bottom of the filter.....
(much like viewtopic.php?f=17&t=5570&p=73894&hilit=fuel+filter#p73894)

ImageIMAG0720 by Justin Drexler, on Flickr

definitely coming from the filter elbow connection rather than the hardline. The fuel was atomising nicely in my face :sick:

The filter was from the club shop. It's possible that i may have accidently backed the filter up trying to align it with the hard line. I'll try again next week, but can anyone suggest any other remedy? cheers :pray: :kiss:

Also, I moaned a few posts back about cylinder No 1 fuel hose not lining up. I've tried every which way to get the thing to fit properly (i.e.) not twisting, but it won't sit happy. When the injector is installed, the top banjo fitting sits vertical, but needs to be horizontal.
ImageIMAG0717 by Justin Drexler, on Flickr
looking at the thing off the car, both ends have been crimped the same (that's to say they both point in the same direction). but i think they should be off set by 30-45 degrees
(the picture here: https://www.deloreango.com/uk/black-sta ... lines.html )

Am i right?
User avatar
InoX
 
Posts: 465
Joined: Sat Jun 20, 2009 2:51 pm

Re: Look what I've got back....

Postby arranj » Sun May 21, 2017 3:07 pm

Filter - PTFE tape - it takes a couple of goes to get it sealed. Or make a thread modification to the elbow as in that link, and use a washer...?

Lines - every one of those lines has different angles, and none of them are labelled. You probably have them the wrong way round, mainly because it's impossible to get them right without them being labelled. No-one knows the right way. Pretty sure this is version you have: https://www.deloreango.com/uk/stainless ... hoses.html - I'd imagine you could swap 2 over and solve this issue.
Arran | DCUK 004 | VIN #1764 | Official DeLorean Club World Headquarters, Norfolk, UK

Das Webmeister
DeLorean Club

Image
User avatar
arranj
 
Posts: 7651
Joined: Fri May 29, 2009 6:19 pm
Location: DeLorean Club World Headquarters, Norfolk, UK
VIN #: 1764
Spaxed

Re: Look what I've got back....

Postby InoX » Sun May 21, 2017 3:26 pm

thanks for that.

I'll give it a go. 8-)

Can't remember are the shorter injector hoses close in length to the csv or the warm up regulator?

hmm. not with the car now. I'll have a look.
User avatar
InoX
 
Posts: 465
Joined: Sat Jun 20, 2009 2:51 pm

PreviousNext

Return to Members Cars or Unique DeLoreans

Who is online

Users browsing this forum: No registered users and 11 guests

About us

The DeLorean Club UK forum for European DeLorean owners and enthusiasts. The largest DeLorean forum in Europe.

Registration is FREE and all registered users get full access