VIN# 16951 - August 1982 - Manual - Black Interior

[Domi]

Thank You
I have ordered the clutch bleeder on John's Hervey website, here is the link:
https://www.specialtauto.com/delorean-p ... ssion.html
I live near the city of Grenoble near the French Alps

[Domi]

New oil pressure sensor

DSCN3362.JPG (60.61 KiB) Viewed 3001 times

Nevertheless, it does not screw everything, please see picture below. Does this happen to anyone else? (I hope it won’t leak oil)

IMG_3607.JPG (64.05 KiB) Viewed 3001 times

IMG_3608.JPG (76.1 KiB) Viewed 3001 times

New wire from the starter to the alternator bigger and longer to avoid heat from the exhaust pipe

IMG_3609.JPG (75.42 KiB) Viewed 3001 times

[Domi]

WUR cleaned

DSCN3363.JPG (79.51 KiB) Viewed 2977 times

DSCN3364.JPG (63.88 KiB) Viewed 2977 times

DSCN3365.JPG (58.54 KiB) Viewed 2977 times

DSCN3366.JPG (94 KiB) Viewed 2977 times

[Domi]

The stainless bracket is back in the engine compartment, and a new coil

DSCN3367.JPG (62.68 KiB) Viewed 2948 times

DSCN3368.JPG (85.56 KiB) Viewed 2948 times

DSCN3369.JPG (99.03 KiB) Viewed 2948 times

[Admin-bloke]

Looking good there Mr Domi, don't forget those vacuum pipes:

viewtopic.php?f=17&t=1030

viewtopic.php?f=17&t=4619

Thanks for sharing

[Domi]

I have bought them from John H. in Red.
Didn't install yet, but soon.
Anyway, thanks for the links, that helps

[Admin-bloke]

I have bought them from John H. in Red.
Didn't install yet, but soon.
Anyway, thanks for the links, that helps

Keep the pictures coming

[Domi]

Sure don' worry

[Domi]

Injectors are ready for a new seal and a new hook

DSCN3370.JPG (49.05 KiB) Viewed 2904 times

Not so easy to remove and to put on the new one
Soak in WD40 and with the help of a 14 wrench push to remove the seal

DSCN3371.JPG (42.41 KiB) Viewed 2904 times

DSCN3372.JPG (42.66 KiB) Viewed 2904 times

DSCN3373.JPG (54.47 KiB) Viewed 2904 times

Same thing in reverse to put the new seal

DSCN3374.JPG (55.46 KiB) Viewed 2904 times

DSCN3375.JPG (65.39 KiB) Viewed 2904 times

Injectors are finally ready

DSCN3376.JPG (73.87 KiB) Viewed 2904 times

With the new stainless steel fuel lines

DSCN3377.JPG (83.78 KiB) Viewed 2904 times

In the engine compartment

DSCN3378.JPG (111.73 KiB) Viewed 2904 times

[Admin-bloke]

Looking great there.

For replacing injector seals, I use a deep socket and a rubber headed hammer to drift them off.

viewtopic.php?f=17&t=119&start=20

It looks like you're almost there