Look what I've got back....

[InoX]

IMAG0624 by Justin Drexler, on Flickr

IMAG0625 by Justin Drexler, on Flickr

IMAG0629 by Justin Drexler, on Flickr

IMAG0630 by Justin Drexler, on Flickr

Think I may have found the two inches I need

IMAG0631 by Justin Drexler, on Flickr

you can see where the pipe was connected to the hose for whatever reason it was pushed onto the metal pipe a good 3". I'll have a play tomorrow to see if i can get it right.

Other news:

IMAG0616 by Justin Drexler, on Flickr

sanded and painted.

IMAG0638 by Justin Drexler, on Flickr

IMAG0617 by Justin Drexler, on Flickr

IMAG0617 by Justin Drexler, on Flickr

IMAG0618 by Justin Drexler, on Flickr

IMAG0620 by Justin Drexler, on Flickr

IMAG0621 by Justin Drexler, on Flickr

IMAG0623 by Justin Drexler, on Flickr

IMAG0622 by Justin Drexler, on Flickr

IMAG0633 by Justin Drexler, on Flickr



IMAG0634 by Justin Drexler, on Flickr

IMAG0635 by Justin Drexler, on Flickr

IMAG0636 by Justin Drexler, on Flickr

IMAG0637 by Justin Drexler, on Flickr

Rad should be going back in tomorrow. If i can ask a stupid question: the new rubber bushes I got for the new rad, I they go between the rad and the brackets, don't they and the bolt head sits on the bracket?

[InoX]

Am I supposed to have four rad mounting rubber washers?

If I do, why did I only order two...

[InoX]

Got the pipes to fit.

IMAG0645 by Justin Drexler, on Flickr


IMAG0644 by Justin Drexler, on Flickr


Radiator is sort of in. need some fastners and a couple of those rubber washers.

IMAG0643 by Justin Drexler, on Flickr

IMAG0642 by Justin Drexler, on Flickr

IMAG0641 by Justin Drexler, on Flickr

IMAG0640 by Justin Drexler, on Flickr

IMAG0639 by Justin Drexler, on Flickr

[arranj]

Am I supposed to have four rad mounting rubber washers?

If I do, why did I only order two...

The parts manual says 4..... I have a feeling I may well have said "2" to you in an email or PM - quite possibly (not sure - sounds like the sort of thing I would do) - so please blame me!

Just measuring pipe now for your peace of mind, but I see you are sorted?

[arranj]

The pipe I have looks nothing like your pipe at all - which probably explains it then. This one is 2 inches longer than yours too.... It may well be that your header tank is mounted a bit higher than OEM too if it's a Hervey one.

What fixings do you need for the radiator install? The 2 bottom bolts, or something to attach the fans to the rad?

[InoX]

I just need two of the rubber washers plus two brackets/ clips to hold the hoses to the pontoon and inside rear bumper. I'll order them tonight. Think the pipe needs to come closer to the pontoon as when I mocked up the pipe to the water pump the hoses started to kink. Deffo need 4 rubber washers or else the rad isn't isolated from the frame. Cheers!

[mec]

where did you get your fans from ? they look like they bolt straight on ?

[InoX]

Toby and Misty. Delorean Parts North West.

https://www.delorean-parts.com/

yes, they did bolt straight on

[InoX]

IMAG0647 by Justin Drexler, on Flickr

centre bit re-leathered and installed on the console complete with mattaligner. Can't wait to install it in the car. If only I hadn't locked myself out.

[MML]

IMAG0647 by Justin Drexler, on Flickr

centre bit re-leathered and installed on the console complete with mattaligner. Can't wait to install it in the car. If only I hadn't locked myself out.

Where did you get the console pad recovered if you don't mind me asking? It looks great.