DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Welcome to the DeLorean Club Forum, this area is for general DeLorean chat

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby RobvdVeer » Wed May 11, 2011 10:28 pm

Thanks for the explanation.

What about the upper balljoints? Do they come with a similar problem/shortage/alternative? Maybe a pair of up/down could do the trick (just thinking out of the box here)?
Rob van der Veer
User avatar
RobvdVeer
 
Posts: 4626
Joined: Mon Aug 17, 2009 6:34 pm
Location: Netherlands
VIN #: 0b111001101111
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Darren C » Wed May 11, 2011 10:36 pm

Completely different style Rob, and readily available.
@classiccarguru1
Darren C
 
Posts: 1162
Joined: Wed Jul 22, 2009 8:55 pm
Location: In the garage, Emsworth. Hants
VIN #: 4532
Spaxed

DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby A Van » Thu May 12, 2011 10:08 am

Darren, the level of detail in your comparisons really helps!!
Like you say we are halfway there, time to start looking at other British around the same time....Bedford etc
At least we have the right body....it's a very good start, I will investigate the Delphi angle
Alistair V

Vin 11753 - B/Auto - Kuwait, painted black
Ex Vin 11766 - B/Auto - Dubai
Ex 11622, 6064

RIP Mike 'Bozzy' Bosworth 19/04/1969 - 31/12/2015


Official Spokesperson and Media Liaison Officer, and off road Buggy flipper
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
A Van
 
Posts: 7821
Joined: Fri May 29, 2009 6:33 pm
VIN #: 11753
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby A Van » Thu May 12, 2011 7:29 pm

Delphi TC170 or FBJ5030

Looks similar, will need to look in greater detail.

Its the 'shaft' we need to get right... (isnt it always :)
Alistair V

Vin 11753 - B/Auto - Kuwait, painted black
Ex Vin 11766 - B/Auto - Dubai
Ex 11622, 6064

RIP Mike 'Bozzy' Bosworth 19/04/1969 - 31/12/2015


Official Spokesperson and Media Liaison Officer, and off road Buggy flipper
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
A Van
 
Posts: 7821
Joined: Fri May 29, 2009 6:33 pm
VIN #: 11753
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Dan 6511 » Thu May 12, 2011 9:37 pm

What about the commer van ones arran found?
Sell it Or Sorn it

Road trips:
2008: Mervyn's Delorean Weekend, Ireland
2008: DMC Europe Open House
2009: DMC Europe Open House
2009: Royal Delorean Weekend, Ireland
2010: Silvercoast, France
2010: Shanefest, Ireland
2010: Luxemburg & Nurburgring
2011: Eurofest, Belfast
2019: International DeLorean Meeting, Hamburg
User avatar
Dan 6511
 
Posts: 3538
Joined: Fri Jun 05, 2009 5:10 pm
Location: Essex

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Darren C » Thu May 12, 2011 9:40 pm

Cheers Al. :D

Now then to continue the analysis the Lotus joint arrived in the post today.

Here's the vital statistics.

Image

Right then, we knew the body was oversize (Phil has had some machined down and re-knurled) and that the shaft was close.
These are my observations:
Size G on the Lotus joint is 16.5mm, bearing in mind you need to machine a circlip slot of 2mm (size E) that only leaves 0.5mm for size D. Granted it's 0.2mm more than the Specialty T joint, but still a little lean for my liking.
Further; the taper is the same but hey look at the length of the shaft (size L) it's 54mm the longest by far of all the joints I've seen.
Now bearing in mind you need to reduce the overall diameter on these joints and then re-knurl the spline back on and cut the circlip grove, it's a lot of work when the shaft is too long to begin with.

Before I totally disregard this joint as an option I'm going to explain further with a TAPER REFERENCE GAUGE I made this evening in my workshop. :ugeek:

Image

This has been cast around the DMCH joint shaft to be totally accurate to the taper. This is almost as good if not better than cutting a hub in half.
@classiccarguru1
Darren C
 
Posts: 1162
Joined: Wed Jul 22, 2009 8:55 pm
Location: In the garage, Emsworth. Hants
VIN #: 4532
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Darren C » Thu May 12, 2011 9:45 pm

Here's how the DMCH OEM Delorean drawing made joint fits in the gauge.

Image

The bottom horizontal line is the datum line from the shoulder of the joint (bottom of your lower arm)
The top line is the end of the taper at the base of the thread.

The distance between these lines is size L in my data.
@classiccarguru1
Darren C
 
Posts: 1162
Joined: Wed Jul 22, 2009 8:55 pm
Location: In the garage, Emsworth. Hants
VIN #: 4532
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby A Van » Thu May 12, 2011 9:46 pm

Ideal Darren!

I think we need to analyse any similar looking 'vintage' joints from some old British cra..I mean cars.

Arran what was the Commer van ref...trying to stop laughing as I type Commer van...its beyond my wildest dreams!
Alistair V

Vin 11753 - B/Auto - Kuwait, painted black
Ex Vin 11766 - B/Auto - Dubai
Ex 11622, 6064

RIP Mike 'Bozzy' Bosworth 19/04/1969 - 31/12/2015


Official Spokesperson and Media Liaison Officer, and off road Buggy flipper
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
A Van
 
Posts: 7821
Joined: Fri May 29, 2009 6:33 pm
VIN #: 11753
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Darren C » Thu May 12, 2011 9:50 pm

Now lets see how a special T VW joint fits in a delorean.

Image

You can see that puts the datum line up by 4mm. This moves the lower arm 4mm away from the hub. This will effect the castor angle, so if you fit specialty T joints then get the alignment checked afterwards. (albeit it's a small amount)

Also note how much further the shaft protrudes the gauge, in reality the DMCH one is below the surface of where the castle nut fits so you have some room here before washers are needed.
Last edited by Darren C on Thu May 12, 2011 10:05 pm, edited 2 times in total.
@classiccarguru1
Darren C
 
Posts: 1162
Joined: Wed Jul 22, 2009 8:55 pm
Location: In the garage, Emsworth. Hants
VIN #: 4532
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Darren C » Thu May 12, 2011 9:53 pm

Now for the lotus joint.

Image

You can see this is getting worse....

After you've spent the time and effort machining it to fit the arm, just look how far it moves the hub from the lower arm.

It's about 8mm out.
@classiccarguru1
Darren C
 
Posts: 1162
Joined: Wed Jul 22, 2009 8:55 pm
Location: In the garage, Emsworth. Hants
VIN #: 4532
Spaxed

PreviousNext

Return to Welcome! ... General DeLorean chat

Who is online

Users browsing this forum: No registered users and 4 guests

About us

The DeLorean Club UK forum for European DeLorean owners and enthusiasts. The largest DeLorean forum in Europe.

Registration is FREE and all registered users get full access