DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Welcome to the DeLorean Club Forum, this area is for general DeLorean chat

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Phil349 » Sat May 14, 2011 12:46 pm

Excellent stuff!!!
I aggree we should have the shafts drilled and use a castle nut and split pin.

The circlip groove is only about 1.5/1.6 mm high on the standard DMC joint, and that is the measurement I modified my elise ones to also. 2mm would have been too large.

Just a question on point 3 Darren, the bottom plate thickness. If the spring tension is pulling the on the joint upwards, trying to pull the ball from the socket, how can the bottom plate bend downwards? maybe when driving and the suspension is moving it could happen over time?
Phil349
 
Posts: 86
Joined: Tue Jul 07, 2009 11:36 pm
VIN #: 1128

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Dan 6511 » Sat May 14, 2011 12:49 pm

I just feel that drilling a hole is just going to weaken the thing. If I were to drill a hole I might do the nut up then drill through the nut and the shaft together and insert a roll pin. I think nyloc would be just fine though personally.
Sell it Or Sorn it

Road trips:
2008: Mervyn's Delorean Weekend, Ireland
2008: DMC Europe Open House
2009: DMC Europe Open House
2009: Royal Delorean Weekend, Ireland
2010: Silvercoast, France
2010: Shanefest, Ireland
2010: Luxemburg & Nurburgring
2011: Eurofest, Belfast
2019: International DeLorean Meeting, Hamburg
User avatar
Dan 6511
 
Posts: 3538
Joined: Fri Jun 05, 2009 5:10 pm
Location: Essex

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby arranj » Sat May 14, 2011 12:57 pm

The castle nuts/split pin was a recall - page 4 here: http://www.dmcnews.com/bulletins/SC-03-1.82.html

But I'm not sure Nylock nuts were used back in those days - and I can't see the problem with a Nylock nut - maybe even two just for the fun of it?!

It's a personal preference thing - it's not exactly difficult for the end user to drill themselves? 97p for a nut from here: http://www.namrick.co.uk/acatalog/U.N.F._Nuts.html
Arran | DCUK 004 | VIN #1764 | Official DeLorean Club World Headquarters, Norfolk, UK

Das Webmeister
DeLorean Club

Image
User avatar
arranj
 
Posts: 7664
Joined: Fri May 29, 2009 6:19 pm
Location: DeLorean Club World Headquarters, Norfolk, UK
VIN #: 1764
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Phil349 » Sat May 14, 2011 1:22 pm

Dan 6457 wrote:I just feel that drilling a hole is just going to weaken the thing. If I were to drill a hole I might do the nut up then drill through the nut and the shaft together and insert a roll pin. I think nyloc would be just fine though personally.


The drilled hole in the shaft is above the nut in effect, at the castleated area of the nut, so above the real used contact area with the shaft where you need the shaft to have strength. If you see what I mean so wont weaken the actual connection between nut and shaft.
A proper castle nut would have as much contact area as a standard nut where its threaded, then the castlated part would be extra on top, so taller over all. The castle nuts that came with the special T joints were very low profile so I didnt use them and got alernative ones.
I would think drilling through the actual nut and shaft together as you describe and sticking a roll pin through will really weaken it overall at the point where you need that strengh.
Nylocks probably would be fine really, but castle nuts can be even better. I think the recall was because they found some nuts were coming loose on their own but I dont know if these were normal nuts or nylocks.

Its not easy to drill the shaft on the car as access can be tricky, better to have the shaft pre drilled then installation will be nice and simple. :)
Last edited by Phil349 on Sat May 14, 2011 1:32 pm, edited 1 time in total.
Phil349
 
Posts: 86
Joined: Tue Jul 07, 2009 11:36 pm
VIN #: 1128

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Daniel Shane » Sat May 14, 2011 1:30 pm

F**king great news.

And it's made in the UK so that's even better !!

I'd go for the nylock nuts and not worry about drilling. All modern cars use nylocks and it make find a replacement nut easy

Dan
Dan Shane
DCUK 008
Ex VIN 4754

The Black Stig
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
Daniel Shane
 
Posts: 461
Joined: Fri Jun 05, 2009 1:29 pm
VIN #: Ex 4754

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby RobvdVeer » Sat May 14, 2011 3:10 pm

Daniel Shane wrote:All modern cars

Quoted for effect
Rob van der Veer
User avatar
RobvdVeer
 
Posts: 4626
Joined: Mon Aug 17, 2009 6:34 pm
Location: Netherlands
VIN #: 0b111001101111
Spaxed

DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby A Van » Sat May 14, 2011 4:53 pm

As a DeLorean is just part of the ' Darren Collins Collection ' it doesn't get used that much so we think it would be prudent to also fit a set to a car which is used a lot, step up Dan Stacey.
Alistair V

Vin 11753 - B/Auto - Kuwait, painted black
Ex Vin 11766 - B/Auto - Dubai
Ex 11622, 6064

RIP Mike 'Bozzy' Bosworth 19/04/1969 - 31/12/2015


Official Spokesperson and Media Liaison Officer, and off road Buggy flipper
DeLorean Club

The Future's Bright....
The Future's
DeLorean Club
User avatar
A Van
 
Posts: 7821
Joined: Fri May 29, 2009 6:33 pm
VIN #: 11753
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby jerzybondov » Sat May 14, 2011 5:59 pm

If Dan can't be arsed to change his, I'm happy to be a guinea pig - my car's going to be piling on the miles this summer...
VIN 7176
Official Club Reaper Extraordinaire.
User avatar
jerzybondov
 
Posts: 2603
Joined: Sun Jun 07, 2009 10:24 pm
Location: London NW2
VIN #: 7176
Spaxed

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby Dan 6511 » Sat May 14, 2011 6:12 pm

Well I want to change to these new type anyway as I don't trust the VW ones.

While I'm in there Im gonna change out the polybush for a rubber one as its crap. Now we need to find a UK source of these too :lol:

Image

I'll change my uppers as well 'while im in there', they are vauxhall viva right?
Sell it Or Sorn it

Road trips:
2008: Mervyn's Delorean Weekend, Ireland
2008: DMC Europe Open House
2009: DMC Europe Open House
2009: Royal Delorean Weekend, Ireland
2010: Silvercoast, France
2010: Shanefest, Ireland
2010: Luxemburg & Nurburgring
2011: Eurofest, Belfast
2019: International DeLorean Meeting, Hamburg
User avatar
Dan 6511
 
Posts: 3538
Joined: Fri Jun 05, 2009 5:10 pm
Location: Essex

Re: DMCH Lower ball joints IS THIS WHY THEY FAIL??????

Postby arranj » Sat May 14, 2011 6:26 pm

Yes Dan: viewtopic.php?f=27&t=1902

We have NOS ones in stock too: viewtopic.php?f=66&t=589
Arran | DCUK 004 | VIN #1764 | Official DeLorean Club World Headquarters, Norfolk, UK

Das Webmeister
DeLorean Club

Image
User avatar
arranj
 
Posts: 7664
Joined: Fri May 29, 2009 6:19 pm
Location: DeLorean Club World Headquarters, Norfolk, UK
VIN #: 1764
Spaxed

PreviousNext

Return to Welcome! ... General DeLorean chat

Who is online

Users browsing this forum: No registered users and 4 guests

About us

The DeLorean Club UK forum for European DeLorean owners and enthusiasts. The largest DeLorean forum in Europe.

Registration is FREE and all registered users get full access